Gyros


SparkFun 6 Degrees of Freedom Breakout - LSM6DS3
The LSM6DS3 is a accelerometer and gyroscope sensor with a giant 8kb FIFO buffer and embedded processing interrupt functions, specifically targeted at the cellphone market. Due to the capabilities and low cost of the LSM6DS3 we’ve created this small breakout board just for you! Each LSM6DS3 Breakout has been designed to be super-flexible and can be configured specifically for many applications. With the LSM6DS3 Breakout you will be able to detect shocks, tilt, motion, taps, count steps, and even read the temperature! The LSM6DS3 is capable of reading accelerometer data up to 6.7kS/s and gyros..
R178.00 (inc VAT)
SparkFun 6 Degrees of Freedom IMU Digital Combo Board - ITG3200/ADXL345
This is a simple breakout for the ADXL345 accelerometer and the ITG-3200 MEMS gyro. With this board, you get a full 6 degrees of freedom. The sensors communicate over I2C and one INT output pin from each sensor is broken out. If you need a simple and tiny board that gives you 6 degrees of freedom, this would be a good choice. Having a hard time picking an IMU? Our Accelerometer, Gyro, and IMU Buying Guide might help! Features: Tiny! Two mounting holes ADXL345 accelerometer ITG-3200 gyro 3.3V input I2C interface Documents: Schematic Eagle Files Datasheet (ITG-3200) Datasheet (ADXL345)..
R711.50 (inc VAT)
SparkFun 9DoF IMU Breakout - LSM9DS1
The LSM9DS1 is a versatile, motion-sensing system-in-a-chip. It houses a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer – nine degrees of freedom (9DOF) in a single IC! The LSM9DS1 is equipped with a digital interface, but even that is flexible: it supports both I2C and SPI, so you’ll be hard-pressed to find a microcontroller it doesn’t work with. This IMU-in-a-chip is so cool we put it on the quarter-sized breakout board you are currently viewing! The LSM9DS1 is one of only a handful of IC’s that can measure three key properties of movement – angular velocity, acceleration, ..
R444.50 (inc VAT)
SparkFun Tri-Axis Gyro Breakout - L3G4200D
This is a breakout board for the L3G4200D low-power three-axis angular rate sensor. The L3G4200D is a MEMS motion sensor and has a full scale of ±250/±500/±2000 dps and is capable of measuring rates with a user-selectable bandwidth. These work great in gaming and virtual reality input devices, GPS navigation systems and robotics. Not sure which gyro is right for you? Our Accelerometer and Gyro Buying Guide might help! Features: Three selectable full scales (250/500/2000 dps) I2C/SPI digital output interface 16 bit-rate value data output 8-bit temperature data output Wide supply voltage: 2..
R889.50 (inc VAT)
SparkFun Triple Axis Accelerometer and Gyro Breakout - MPU-6050
The MPU-6050 is a serious little piece of motion processing tech! By combining a MEMS 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an onboard Digital Motion Processor™ (DMP™) capable of processing complex 9-axis MotionFusion algorithms, the MPU-6050 does away with the cross-axis alignment problems that can creep up on discrete parts. Our breakout board for the MPU-6050 makes this tiny QFN package easy to work into your project. Every pin you need to get up and running is broken out to 0.1" headers, including the auxiliary master I2C bus which allows the M..
R711.50 (inc VAT)
9 Degrees of Freedom - Razor IMU
The 9DOF Razor IMU incorporates three sensors - an ITG-3200 (MEMS triple-axis gyro), ADXL345 (triple-axis accelerometer), and HMC5883L (triple-axis magnetometer) - to give you nine degrees of inertial measurement. The outputs of all sensors are processed by an on-board ATmega328 and output over a serial interface. This enables the 9DOF Razor to be used as a very powerful control mechanism for UAVs, autonomous vehicles and image stabilization systems. The board comes programmed with the 8MHz Arduino bootloader (stk500v1) and some example firmware that demos the outputs of all the sensors. Sim..
R1,334.00 (inc VAT)
SparkFun 9 Degrees of Freedom - Sensor Stick
The SparkFun 9DOF Sensor Stick is a very small sensor board with 9 degrees of freedom. It includes the ADXL345 accelerometer, the HMC5883L magnetometer, and the ITG-3200 MEMS gyro. The ‘stick’ has a simple I2C interface and a mounting hole for attaching it to your project. Also, the board is a mere 0.036" thick (0.093" overall), allowing it to be easily mounted in just about any application. Having a hard time picking an IMU? Our Accelerometer, Gyro, and IMU Buying Guide might help! Dimensions: 1.37x0.42" Documents: Schematic Eagle Files Datasheet (ADXL345) Datasheet (HMC5883L) Datasheet..
R889.50 (inc VAT)
SparkFun Gyro Breakout - LPY503AL (Dual 30°/s)
This is a breakout board for the ST’s dual-axis LPY503AL gyro.  The LPY503AL is a MEMS motion sensor that measures angular velocity along the pitch and yaw axes with a full scale of ±30°/s. Two different analog outputs are provided for both the x- and z- axes - one 1x amplified and the other 4x amplified. A regulated voltage between 2.7 and 3.6VDC should be supplied to the power pins. We have the filtering circuits all set up; you’ll just need to connect the outputs to an ADC, and you’re ready to go. This breakout board includes the gyro and all necessary filtering capacitors as shown. The..
R533.50 (inc VAT)
SparkFun UDB5 - PIC UAV Development Board
Our UAV Development Board is back! The UDB5 (UAV Development Board version 5) comes populated with a dsPIC33FJ256 CPU, and the impressive MPU-6000, a MEMS 3-axis gyroscope and 3-axis accelerometer. The on-board Invensense gyro even has enough vibration tolerance to be used in RC heli applications. By itself, the board can be used to develop a three axis IMU controller. By addition of an EM406 or D2523T GPS receiver, it can be used to develop a UAV controller for an RC car, plane, helicopter, or boat. It comes with self-testing firmware that can serve as a starting point for you to develop yo..
R1,423.00 (inc VAT)
SparkFun Triple-Axis Digital-Output Gyro Breakout - ITG-3200
This is a breakout board for InvenSense’s ITG-3200, a groundbreaking triple-axis, digital output MEMS gyroscope. The ITG-3200 features three 16-bit analog-to-digital converters (ADCs) for digitizing the gyro outputs, a user-selectable internal low-pass filter bandwidth, and a Fast-Mode I2C (400kHz) interface. Additional features include an embedded temperature sensor and a 2% accurate internal oscillator. The ITG-3200 can be powered at anywhere between 2.1 and 3.6V. For power supply flexibility, the ITG-3200 has a separate VLOGIC reference pin (labeled VIO), in addition to its analog supply ..
R444.50 (inc VAT)

Store Information