IoT


Photon Header - 12 Pin Female
These standard female headers are made to work with the Particle Photon and Photon ProtoShield boards. Each header adds a great deal of connectivity to your next Photon project. Each order includes one 1x12 female header with pins that are spaced by 0.1". If you don’t have a Particle Photon, that’s fine! These headers will work in any other situation when you need a 12-pin header solution! Documents: Datasheet ..
R12.00 (inc VAT)
Photon Stackable Header - 12 Pin
These stackable headers are made to work with the Particle Photon and Photon ProtoShield boards. Each header adds a great deal of connectivity to your next Photon project. Each order includes one 1x12 stackable header with pins spaced at 0.1". If you don’t have a Particle Photon, that’s fine! These headers will work in any other situation when you need a 12-pin header solution! Documents: Datasheet ..
R12.00 (inc VAT)
SparkFun ESP32 Thing Power Control Shield
The SparkFun ESP32 Thing Power Control Shield enables the ESP32 Thing to switch up to 5A of a DC load, providing a wide variety of options to control your next project! With a default voltage range of 5–28VDC, power can be connected to this shield in one of two ways. The first is the barrel connector, but with a maximum current rating of 2.5A (designed for light loads). The second option is on the 3-pin screw terminal, which has connections for VCC, ground and a 5V output. The supply voltage is regulated down to 5V to power the ESP32 Thing, as well as a fan to keep the board cool under heavy l..
R593.00 (inc VAT)
SparkFun Photon IMU Shield
This is the SparkFun Photon IMU Shield, a versatile motion-sensing add-on board for your Photon device. Each IMU shield is equipped with an on-board LSM9DS1 system-in-a-chip that houses a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer. That’s right, 9 degrees of freedom (9DOF) from a single IC! Each sensor in the LSM9DS1 supports a large variety of ranges: the accelerometer’s scale can be set to ± 2, 4, 6, 8, or 16 g, the gyroscope supports ± 245, 500, and 2000 °/s, and the magnetometer has full-scale ranges of ± 2, 4, 8, or 12 gauss. The SparkFun Photon IMU Shield comes with..
R444.50 (inc VAT)
SparkFun Photon Micro OLED Shield
The SparkFun Photon Micro OLED Shield breaks out a small monochrome, blue-on-black OLED to use with your Photon module. It’s “micro”, but it still packs a punch – the OLED display is crisp, and you can fit a deceivingly large amount of graphics on there. This shield is perfect for adding graphics to your Photon, displaying diagnostic information without resorting to serial output, and teaching a little game theory. Speaking of, the screen on this breakout is only 64 pixels wide and 48 pixels tall, measuring 0.66" across. In total, the Micro OLED Shield provides access to 16 of the OLED’s pins..
R356.00 (inc VAT)
SparkFun Photon ProtoShield
You can’t have any development board without some sort of prototyping area, the SparkFun Photon ProtoShield takes care of this. This ProtoShield mates easily with your Photon module and provides a small soldering area and separated power and I2C hook-ups. With the SparkFun Photon ProtoShield you have the control over what kind of project you design for your Photon. The Particle Photon is a tiny WiFi development kit for creating connected projects and products. Sporting a 120MHz ARM Cortex M3 and built-in WiFi, the Photon is not only powerful, but easy to use. The small form factor is ideal fo..
R44.50 (inc VAT)
SparkFun Photon Wearable Shield
The SparkFun Photon Wearable Shield makes it easy to add the WiFi-enabled Photon to any wearables project. Each pin on the Photon is broken out into large sewing pins. Use conductive thread to make your next wearables projects. The large pins are also great for using conductive paint to create any project that needs WiFi. There are even optional smaller pins for soldering flexible wires. The SparkFun Photon Wearable Shield comes with the headers already soldered on, so you can plug and play! This version uses a 0.8mm thick PCB (as opposed to the standard 1.6mm), which is easier to sew into yo..
R89.50 (inc VAT)
SparkFun Photon RedBoard
The SparkFun Photon RedBoard, to put it simply, is a WiFi/Microcontroller development board in the Arduino form-factor for the Photon. It’s easy to use, it’s powerful, and it’s connected to the cloud. With the best support, potential, and performance the Photon RedBoard provides you with an IoT device with a powerful 120MHz ARM Cortex M3 and built-in WiFi connectivity. Imagine blowing up a Photon into the shape of an Arduino and while keeping its wireless and ARM Cortex M3 capabilities, the result is this board! The SparkFun Photon RedBoard has been based around the P1 Particle Module. Each P..
R741.00 (inc VAT)
SparkFun Photon Wearable Shield
The SparkFun Photon Wearable Shield makes it easy to add the WiFi enabled Photon to any wearables project. Each pin on the Photon is broken out into large sewing pins. Use conductive thread to make your next wearables projects. The large pins are also great for using conductive paint to create any project that needs WiFi. There are even optional smaller pins for soldering flexible wires. The SparkFun Photon Wearable Shield comes with the headers already soldered on, so you can plug and play! The Particle Photon is a tiny WiFi development kit for creating connected projects and products. Sport..
R89.00 (inc VAT)
ESP32 Thing Stackable Header Set
These headers are made to work with the SparkFun ESP32 Thing and ESP32 Power Control Shield boards. Each set of headers makes your ESP32 Thing easily stackable with the Power Control Shield or other applications. This set includes two 1x20 headers, enough to connect your ESP32 to anything you want! Includes: 2x 20-pin Stackable Header Documents: Dimensional Drawing ..
R28.00 (inc VAT)
SparkFun Photon Battery Shield
The SparkFun Photon Battery Shield provides you with an easy way to power your Photon module with a Lithium Polymer (LiPo) battery. Not only can the Battery Shield power your Photon, but you will also be able to charge a LiPo battery through it. The board comes with a JST connector for your single-cell LiPo battery and utilizes the Photon’s on-board micro-USB connector for the charge input. This battery shield uses a MCP73831 for LiPo charging and a MAX1704X for fuel gauging. This is a very simple shield for your Photon to provide it basic and on-the-go power wherever and whenever you might n..
R237.00 (inc VAT)
SparkFun Photon Weather Shield
The SparkFun Photon Weather Shield is an easy to use add-on board that grants you access to barometric pressure, relative humidity, and temperature. There are also connections on this shield to optional sensors such as wind speed, direction, rain gauge and soil readings! These Weather Shields utilize the HTU21D humidity and MPL3115A2 barometric pressure sensors. Each shield comes with two RJ11 connectors (for optional hook up of rain and wind sensors) and a 3-pin soil temperature and moisture hookups. Finally, each Weather Shield can attach effectively and easily to your Photon in no time at ..
R443.50 (inc VAT)

Store Information