Please Note: Our last order from Sparkfun for 2017 will be Friday, 8 December 2016 and this stock will arrive Wednesday, 13 December 2017.
Although backorders can still be placed online after this, we can only import the stock again Tuesday, 2 January 2018.
Riecktron wishes you a Merry Christmas and Happy New Year for 2018. Thank you for your support the past 11 years.

Tools


SparkFun Mini Screwdriver
This is just your basic reversible screwdriver - pocket sized! Both flat and phillips heads available. Comes with pin clip and snazzy SparkFun logo. ..
R22.00 R19.40
Digital LED Voltmeter
This Digital LED Voltmeter measures the voltage at a particular point of the system it has been hooked up to and then provides a readout on its three 7-segment LEDs. This voltmeter is able to provide a readout of voltages from 2.5VDC to 30VDC within a 1% accuracy. Features: Range: 2.5VDC — 30VDC Display: Three 0.28" Red 7-Segment LEDs Refresh Rate: ~1sec Accuracy Within 1% ..
R29.50 (inc VAT)
Solder Leaded - 15-gram Tube
This is your basic tube of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 15 grams (around 5ft). Easy to solder with - recommended for beginners. Mix: 63% Sn / 37% Pb..
R29.50 (inc VAT)
Needle Nose Pliers
Mini Pliers. These are great little pliers! A must have for any hobbyist or electrical engineer. Crucial for inserting devices into bread boards and bending pins. 4" long. ..
R29.50 (inc VAT)
Polymorph - 250g
Polymorph is a non-toxic, biodegradable polyester with a low melting temperature of about 60°C (140°F). Prototype plastic parts can be made by simply heating the plastic beads in hot water until they turn clear and then kneading them together and shaping by hand. When it cools it becomes a nylon-like white plastic. Polymorph can be re-used by simply re-heating and re-shaping. Plastic beads are supplied in a heat-sealed plastic bag to prevent spillage during transport. So what do you do with it? Robotics, small-parts prototyping, arts/crafts, there’s almost no end to what you can do with thi..
R207.50 (inc VAT)
Relay SPDT Sealed
These are high quality Single Pole - Double Throw (SPDT) sealed relays. Use them to switch high voltage, and/or high current devices. This relay’s coil is rated up to 12V, with a minimum switching voltage of 5V. The contacts are rated up to 5A (@250VAC, 30VDC). Note: In the Datasheet below there is a pin layout listed as “Bottom View.” Be aware, this pin layout is actually the top-down view NOT bottom-up. Features: 5V DC SPDT Relay Rated up to 5A Fully Sealed Documents: Datasheet ..
R53.50 (inc VAT)
Wire Strippers - 30AWG (Hakko)
These are extremely handy and comfortable to use wire strippers from Hakko. These are an essential part to any hacker’s arsenal and are able to strip 30AWG wire wrap wire nicely as well as the standard 22AWG hook up wire. Features: 30, 28, 26, 24, 22, 20 AWG settings 0.2, 0.3, 0.4, 0.5, 0.6, 0.8 mm settings Documents: Product Video ..
R230.00 (inc VAT)
Barrel Jack Extension Cable - M-F (6 ft)
Do you fear that your power may not be “far reaching” enough? How would another 6' work for you? Okay, so it doesn’t sound very dramatic, but sometimes an extra 6' of power cable is exactly what your project needs. Don’t hack apart a nice clean barrel jack connection just because it won’t reach, this male-to-female barrel jack extension cable will make the reach. This cable is terminated with 5.5x2.1mm barrel connectors, one male and one female, and fits most of our products that use a DC barrel jack for power (RedBoard, RaspiRobot board, etc.) Features: 6' Long, 5.5x2.1mm Barrel C..
R37.00 (inc VAT)
Diagonal Cutters
Mini Diagonal Cutters. These are great little cutters! A must have for clipping leads and extra solder tails. 4" long...
R29.50 (inc VAT)
Digital Multimeter - Basic
The digital multimeter (DMM) is an essential tool in every electronic enthusiasts arsenal. The SparkFun Digital Multimeter, however, is not your average multimeter, it features a loud continuity sound, current/voltage sense, and quality probes. You can use the multimeter to measure DC and AC voltage, DC current, resistance, continuity, and test diodes. With this version we’ve done away with the bright flashy colors that can get us into trouble and gone with a nice, neutral gray. This multimeter should provoke no strong feelings one way or the other, we know this because our guts say “maybe.” ..
R267.00 (inc VAT)
Heat Shrink Kit
We love heat shrink! We use it for all sorts of handy projects. Use it to reinforce connections, protect devices, and electrically isolate exposed solder joints. We worked with a manufacturer to create a kit that we would use: lots of colors, lots of sizes, nothing too long. We specially requested some of the sizes with heat sensitive glue which significantly increases stress relief and water proofing. This kit includes 95 pieces of heat shrink, all of varying colors and sizes, and comes in a clear bag. All pieces are 10cm in length. Bag includes the following diameters, 5 pieces of each: ..
R118.50 (inc VAT)
Pocket Screwdriver Set
What should every hacker have available to them? That’s right, a screwdriver (you have to get into those cases somehow). What makes screwdrivers even better is when there are a variety of interchangeable bits to use in different situations as you need them. This Pocket Screwdriver Set provides you with just that service in a small, portable package. Each Pocket Screwdriver Set offers 7 different chrome vanadium bits, four flathead options and three Phillips head options, that fit snuggly in the quick-change magnetic holder at the tip of the screwdriver. The screwdriver’s body is made from a h..
R58.00 (inc VAT)
Solder Lead Free - 100-gram Spool
This is your basic spool of lead free solder with a water soluble resin core. 0.031" gauge and 100 grams. This is a good spool for more advanced users that should last 6-12 months depending on how often you solder. If you are just beginning to solder, we recommend you order the leaded solder. Lead-free solder is a bit harder to use (does not flow as well). Mix: 99.3% Sn / 0.7% Cu Documents: MSDS ..
R148.00 (inc VAT)
Soldering Tip - Hakko - 3mm Bevel (T18-C3)
This is a replacement soldering tip for our Hakko FX-888 soldering iron. This is a bevel type of soldering tip. Replacing the tip is very easy - simply unscrew the shield, slip the replacement tip in, and screw the shield back on. Documents: Dimensional Drawing ..
R178.00 (inc VAT)
Hobby Knife Replacement Blades
If you use your hobby knife a lot, chances are you will need extra blades. These #11 blades are very sharp and good for trimming all sorts of things. Each pack comes with 5 blades that work with our hobby knife listed below...
R44.50 (inc VAT)
USB Digital Multimeter - Auto-Ranging (RS232 Output)
It seems like everything plugs in to your computer these days, and this digital multimeter is no exception. This auto-ranging multimeter will test AC and DC voltage and current as well as capacitance, resistance, frequency and even temperature. It features a large, easily readable display for use in the field as well as the ability to connect to your computer for data logging, processing and analysis. It has all of the basic functions that you expect from a good digital multimeter including continuity check (with buzzer), diode test and data hold. Data logging and analysis software is included..
R1,245.50 (inc VAT)
6" Digital Calipers
Digital calipers are an absolute essential. Here at SparkFun we use them all the time. These premium calipers come with an extra battery and auto shut-off. Measurements can be taken in either metric or standard. The calipers are 6" in length and make a great addition to any tool set. These come with two 1.5V LR44 button cell batteries. Documents: Datasheet Battery Hack Tutorial Product Video ..
R267.00 (inc VAT)
9V to Barrel Jack Adapter
This simple cable has so many uses! Plug the 9 volt battery clip onto a standard 9V battery and connect the other end to anything with a 5.5x2.1mm, center-positive barrel jack. Use this cable to battery-power any device that needs 9V and has an on-board barrel jack - it works great for Arduinos, development boards, evaluation boards, and more!..
R52.00 (inc VAT)
ABS Filament 3mm - 1kg (Black)
This is a 1kg (2.2lb) reel of 3mm black ABS (acrylonitrile butadiene styrene) plastic filament for 3D printing. ABS is a great general purpose filament with high strength and good print quality. ABS is one of the most popular 3D printing materials available due to its strength and ease of printing. This filament is an incredibly durable plastic that can be used in prototypes or even the parts found on your TAZ 3D printer! ABS prints can be sanded or smoothed using an advanced technique with acetone. With this technique, you can have ABS parts that are glossy and smooth, while simultaneously s..
R1,245.50 R1,117.20
Adam Tech Wall Adapter Cable (EU)
These Adam Tech Wall Adapter Cables are terminated with a standard European (CEE 7/7) plug at one end and three insulated spade terminal connectors at the other. Each cable is 1m long and provides a safe and appropriate way to hook up our Mean Well power supplies! Each spade terminal has been colored for your convenience and can be found in the Dimensional Drawing below. Documents: Dimensional Drawing ..
R104.00 (inc VAT)
Adam Tech Wall Adapter Cable (NA)
These Adam Tech Wall Adapter Cables are terminated with a standard North American (NEMA 5–15P) plug at one end and three insulated spade terminal connectors at the other. Each cable is 1m long and provides a safe and appropriate way to hook up our Mean Well power supplies! Each spade terminal has been colored for your convenience and can be found in the Dimensional Drawing below. Documents: Dimensional Drawing ..
R104.00 (inc VAT)
Alligator Clip
A staple for the electrical engineer. I can’t tell you how many times I’ve been one clip short! Note: Sold as a single unit...
R6.00 (inc VAT)
Alloy 910 Filament 2.85mm - 0.45kg (Natural)
This is a 0.45kg (1lb) reel of 2.85mm “natural-colored” Alloy 910 nylon co-polymer filament for 3D printing. Specially developed to exhibit the ideal characteristics of several different classes of 3D printing filaments, Alloy 910 offers the strength and durability of nylon with the same minimal shrink nature of PLA. Alloy 910 makes for ideal material to be used in frames or enclosures that are subject to stress and high impact, and items exposed to repeated flexing such as buckles and clasps. Alloy 910 is among the strongest materials you can currently 3D print. When printed, it has a tensil..
R1,037.50 (inc VAT)
Analog Panel Meter - 0 to 5 VDC
This analog panel meter measures DC voltage from 0-5 volts with 2.5% accuracy. It has a clear and easy to read scale and an adjustable dial. These come in handy for measuring the output of sensors with 5V ranges. The face of the meter is 45x45mm overall. The mounting hole should be 38mm. The overall depth of the meter is 35mm. Documents: Product Sheet ..
R104.00 (inc VAT)
ATX Power Supply Connector - Right Angle
This is a right-angle, 24-pin Molex Mini-Fit Jr.™ connector, commonly used as the power supply connector on ATX motherboards. Two rows of twelve pins are broken out two rows of through-hole male headers. See the datasheet below for pin spacing dimensions. Pair this connector with a standard computer power supply and you can source a number of different voltages (+3.3V, +5V, +12V, -12V, -5V) to your project.[ Documents: Dimensional Drawing ..
R29.50 (inc VAT)
Barrel Jack to 2-pin JST
Two pin JST connector to a 2.1x 5.5mm barrel jack, 6.25 inch long jumper cable. We use this cable to adapt from a wall power supply to a relatively small, SMD JST connector. We found that many of the SMD connectors used for battery charging were too large or were not capable of through-putting the current we wanted for faster charging. This setup, with a SMD JST connector and wall power supply, can handle up to 2A!..
R59.50 (inc VAT)
Breadboard - Giant
Description: This is one giant solderless breadboard! It has 7 power buses, 40 columns, and 63 rows - with a total of 3220 tie in points. All pins are spaced by a standard 0.1". The two sets of five columns are separated by about 0.3", perfect for straddling a DIP package over. The board accepts wire sizes in the range of 20-29AWG. This board also has 4 binding posts, a black aluminum plate backing, and 4 rubber standoffs to keep your breadboard suspended safely on your workstation. Dimensions: 9.25 x 8.0 x 1.25" (234.95 x 203.2 x 31.75mm) Documents: Product Video ..
R444.50 (inc VAT)
Breadboard - Mini Modular (Blue)
This blue Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple circuits; They’re also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board. It has a peel and stick adhesive backing as well as two mounting holes for M2 screws so you can anchor it down. Note: These will not connect securely with our older model and are not numbered or lettered. Features: 47 x 35 x 10mm ..
R59.50 (inc VAT)
Breadboard - Mini Modular (White)
This white Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple circuits; They’re also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board. It has a peel and stick adhesive backing as well as two mounting holes for M2 screws so you can anchor it down. Note: These will not connect securely with our older model and are not numbered or lettered. Replaces:PRT-11658 Features: 47 x 35 x 10mm ..
R59.50 (inc VAT)
Breadboard - Translucent Self-Adhesive (Red)
Description: How could anyone improve on the clear plastic breadboard. I mean, that’s pretty sweet right? What if it was red? This translucent red breadboard is probably the coolest looking regular, solderless breadboard there is. It has 2 power buses, 30 columns, and 10 rows - a total of 400 tie in points. All pins are spaced by a standard 0.1". The two sets of five rows are separated by about 0.3", perfect for straddling a DIP package over. The board accepts wire sizes in the range of 29-20AWG. This board also has a self-adhesive on the back. The boards also have interlocking parts, so..
R89.00 (inc VAT)
Bridge Filament 3mm - 0.45kg (Clear)
This is a 0.45kg (1lb) reel of 3mm “clear” Bridge nylon co-polymer filament for 3D printing. Taulman’s “Bridge” high-strength nylon co-polymer bridges the strength of nylon 645 and the ease of printing of ABS/PLA. Items printed in Bridge nylon filament are stronger and more resilient than parts printed in more common materials. Since Bridge prints cleanly and easily, you can print complex models that are ready to be used. The combination of strength, reduced shrinkage and ease in printing allows you to go from 3D model to 3D printed part ready to be installed. The material comes on a heavy-du..
R504.00 (inc VAT)
Bus Pirate - v3.6a
The Bus Pirate v3.6a, created by Ian Lesnet, is a troubleshooting tool that communicates between a PC and any embedded device over 1-wire, 2-wire, 3-wire, UART, I2C, SPI, and HD44780 LCD protocols - all at voltages from 0-5.5VDC. This product eliminates a ton of early prototyping effort when working with new or unknown chips. Working with the Bus Pirate is simple and effective - type commands into a terminal on your computer, those commands are interpreted by the Bus Pirate and sent via the proper protocol. The Pirate will also interpret data sent from your embedded device back to your compu..
R533.50 (inc VAT)
Bus Pirate Cable
This is an interface cable for the Bus Pirate, designed to connect to its 2x5 I/O header. The cable’s connector is composed of two rows of five 0.1" spaced pins; it’s also polarized, as is the mating connector on-board the Bus Pirate, so you can only connect the cable in one direction. The leads of the cable are terminated with female ends to mate with test hooks. The pin-out of the connector is documented here...
R89.00 (inc VAT)
Butane Soldering Tip - Weller - Double Flat (1.0mm)
This is a replacement soldering tip for the Weller Portasol Butane Soldering Iron Kit. The double-flat type tip is 1mm wide. Replacing the tip is a breeze — simply unscrew the currently attached tip with a flat-head screwdriver, slip the replacement tip in, and screw it into place. The double-flat Weller tip has been pre-tinned with a lead-free alloy...
R237.00 (inc VAT)
Chapman Pocket Screwdriver Set
The Chapman Pocket Screwdriver Set is a unique addition to the screwdriver family, as it utilizes a ¼" ratchet, similar to one found on a socket wrench, as well as four custom-built drive bits. This pocket screwdriver is aptly named for its size — not only fitting in your pocket but also fitting into tight spaces where a normal-sized screwdriver would not be able to fit. Moreover, to change the direction you need the screw to go, just flip the pocket screwdriver over! The two Phillips and two flat bits included in the set have been crafted to feature a ball detent for a snug fit inside the 20..
R326.00 (inc VAT)
Digilent Analog Discovery 2
The Digilent Analog Discovery 2 is a USB oscilloscope and multi-function instrument that allows users to measure, visualize, generate, record, and control mixed-signal circuits of all kinds. Developed in conjunction with Analog Devices and supported by Xilinx University Program, the Analog Discovery 2 is small enough to fit in your pocket, but powerful enough to replace a stack of lab equipment, providing engineering students, hobbyists, and electronics enthusiasts the freedom to work with analog and digital circuits in virtually any environment, in or out of the lab. The analog and digital i..
R8,005.50 (inc VAT)
Digilent BNC Adapter Board
The Digilent BNC Adapter Board is a simple add-on board intended to be used with the Digilent Analog Discovery 2, which allows you to use standard BNC-terminated test leads and probes with your pocket-sized oscilloscope. The adapter board provides BNC terminations to each of the two oscilloscope channels and enables you to AC couple or DC couple signals to the oscilloscope in the Analog Discovery. Each channel of the oscilloscope can be selected as AC or DC, coupled by adjusting the jumper that is located behind that channel’s BNC input connector. In addition, the two AWG channels are equippe..
R504.00 (inc VAT)
DSO Quad - Pocket Digital Oscilloscope (Black)
The Black DSO Quad is an open-source pocket-sized 4-channel digital oscilloscope. It’s based on the ARM cortex M3 32-bit platform, providing 72MS/s sampling rate with integrated FPGA and high speed ADC. The Internal 2MB memory can even store waveforms in various formats which you can transfer to your computer using a mini-USB cable. Note: Check the link below for the most up-to-date firmware. Note: This item may take longer to process due to battery installed in the equipment and therefore does not qualify for same-day shipping policy. Additionally, these batteries can not be shipped via Gro..
R5,633.50 (inc VAT)
Electronic Snippers
While our small diagonal cutters are great for hobby use, sometimes you need something with a little more bite. These electronic snippers are great for cutting wires and component leads. They have a cushioned handle which makes them much more comfortable to use. These snippers can be used are wire cutters if the need be, and are great if you’re looking for something a little better than hobby grade...
R356.00 (inc VAT)
Flush Cutters - Hakko
These are our new and improved flush cutters, giving you a way to cut leads very cleanly and close to the solder joint. Diagonal cutters are good, but if you really need to get up close and personal, flush cutters are the way to go. They have a nice spring-action and a comfy grip. Plus, the color combination of red and black is fetching, I must say...
R148.00 (inc VAT)
Global Power Supply - 15V 4.34A
This isn’t your ordinary power supply. The Global Power Supply is a 15V, 4.34A power device specifically designed to work with the JustBoom Amp HAT for the Raspberry Pi. Additionally, as this is a “global” power supply, each order includes plug adapters for the United States, United Kingdom, EU and Australia. This supply is capable of high loads, so we recommend that you exercise caution while using it. Features: Universal / Full-range AC input Power Supply Output Type: Fixed No. of Outputs: 1 Output/Input Voltage AC Min: 90V Input Voltage AC Max: 264V Output Power Max: 65W Output Voltage —..
R889.50 (inc VAT)
Hakko FX888D Soldering Station
For over 50 years, Hakko has been producing superior quality soldering and desoldering tools. They’re dependable, a good value and they work really well! We use Hakko irons in production and we think they’re great. The Hakko FX-888D is an updated digital version of the popular FX-888 and includes several new features. Selectable preset temperatures and digital calibration make it easier to setup and operate, and the new password protection and low temperature alarm provide process control and helps protect against cold solder joints! Please be aware that this soldering iron is for 120VAC powe..
R2,490.50 (inc VAT)
Heatsink Compound
This is a 5g syringe of white heatsink compound (aka thermal grease, thermal paste, thermal goo). Use this whenever you’re connecting a component to a heatsink, it’ll really help to dissipate even more potentially damaging heat. This compound is composed of 50% silicone, 20% carbon, and 30% metal oxide. It has a thermal conductivity of 1.172 W/(mK), which should be plenty for voltage regulators, MOSFETs, motor drivers, audio amplifiers, etc. Features: Color: White Thermal Conductivity: 1.172 W/(mK) Thermal Impedance: 0.195 -in2/W Specific Gravity: 2.3 @25°C Evaporation: 0.001% - 24 hrs @1..
R29.50 (inc VAT)
Heatsink TO-220
Small heat sink for TO-220 components. Ideal for keeping your 5V and 3.3V regulators running cool. Black anodized bolt on type with 2.5W dissipation...
R15.00 (inc VAT)
Hex Key - Plas-T-Key T Handle (Straight End, 7/64")
This is a T-Handle 7/64" Hex Key from Allen. The Plas-T-Key is Allen’s standard handle and features a plastic grip, which provides durability and extra torque while in use. Each hex key is 2.125" long with a shaft composed of a black oxide-finished, tempered steel alloy that is terminated in a straight end. These hex keys can be used in a variety of ways, including robotics or for the 6-32 screws used by most Actobotics products...
R104.00 (inc VAT)
Hex Key Set - Metric (Ball End, 9 Pieces)
This is a set of nine high-quality hex keys from Allen. Each key in this set is equipped with a ball end, allowing an entry angle up to 25° in the screw to work in hard-to-reach areas. These specific keys utilize the metric measurement system. These are the go-to hex keys we prefer to use when metric is involved! Each hex key is composed of a black oxide-finished, tempered steel alloy and comes in a noninterference, hinged “caddy” to provide easy access. All hex keys are precision-formed to exact dimensional tolerances for precise fit. Includes: 1x 1.5mm Hex Key 1x 2mm Hex Key 1x 2.5mm Hex..
R593.00 (inc VAT)
Hex Key Set - SAE (Ball End, 13 Pieces)
This is a set of 13 high-quality hex keys from Allen. Each key in this set is equipped with a ball end, allowing an entry angle up to 25° in the screw to work in hard-to-reach areas. These specific keys utilize the United States customary system (sometimes referred to as Imperial). These wrenches will work for any SAE (Society of Automotive Engineers) parts. Each hex key is composed of a black oxide-finished, tempered steel alloy and comes in a noninterference hinged “caddy” to provide easy access. All hex keys are precision-formed to exact dimensional tolerances for precise fit. Includes: ..
R474.50 (inc VAT)
Hot-air Rework Nozzles - Y1126
Hot-air rework nozzles compatible with all of our rework stations. Sold in single units by model number. Documents: Spec Sheet ..
R341.00 (inc VAT)
Hot-air Rework Replacement Element - Temp Controlled
Here’s a replacement heating element for our hot-air rework stations. It’s compatible with Sunkko stations and our own branded rework station. The element is the same for other manufacturers and the connector can be modified by a skilled user to work with other manufacturers. This element includes a thermocouple element at the tip of the air flow with two wires to be connected to a temperature sensing circuit...
R356.00 (inc VAT)
Hot-air Rework Station - 303D
This hot-air rework station is great for professionals and hobbyists in need of tight temperature tolerances and large air flows. This unit displays a digital readout of the actual air temperature with a flow rate of up to 23L per minute. This very powerful unit can be used for multiple applications including standard SMD reflow/repair/removal, thermal IC stress testing, thermoplastic welding, and shrink-wrapping. Includes: 303D Hot Air Rework Station Wand Holder x2 Round Nozzle Tips Features: Closed-loop temperature control Heats up quickly Anti-static design Intelligent cooling syste..
R2,520.00 (inc VAT)

Store Information