Hook Up


2x5 Pin IDC Ribbon Cable
Simple IDC ribbon cable. Used for AVR programming, general communication, and all around handy-ness. Datasheet shows an incorrect length. Cable length is 6" Documents: Datasheet ..
R29.50 (inc VAT)
Ribbon Cable - 10 wire (15ft)
Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing makes a project look more finished than a nice clean wiring harness. This is a 15ft. length of 10-wire ribbon cable. Check the related products below for crimp-on connectors that will fit this cable. Documents: Datasheet ..
R89.00 (inc VAT)
UHF RFID Cable (TNC to RP-SMA)
This is a very simple 1m long TNC to RP-SMA cable. We like to use this cable to connect our ultra high-frequency RFID antennas to an equally powerful reader board. This cable is perfect for extending pre-existing cables to give yourself a better range of operations when managing your RFID projects. Each cable is capable of a nominal impedance of 50? with a cutoff frequency of 39GHz. If you are looking for a good antenna to pair this cable with, we recommend our UHF RFID Antenna. Note: If you are looking to use this cable with the UHF RFID Antenna and the Simultaneous RFID Reader, you will al..
R118.50 (inc VAT)
Banana to Alligator Cable
These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables come in red/black pairs. Features: 36" long ..
R74.00 (inc VAT)
Banana to Alligator Coax Cable
These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. High quality coax cable with stress relief sleeves. Features: 36" long ..
R96.50 (inc VAT)
Banana to Banana Cables
These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables come in red/black pairs. Features: 36" Long ..
R104.00 (inc VAT)
BNC Probe Kit
The BNC probe kit includes a 20MHz professional probe with hook and tip as well as a couple converters to connect the probe to either a BNC jack, RCA jack, or a PCB mount. Each Probe is 4ft (1.2m) in length and is perfect for most midrange applications. This kit was designed for use with our Digital Oscilloscope Kit, but can be used in a variety of other way or with other parts. Includes: 20MHz professional probe with tip, hook connector and ground alligator clip BNC-to-RCA(male) converter BNC-to-PCB mount converter ..
R296.50 (inc VAT)
BNC to Alligator Cable
These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Features: 36" Long ..
R104.00 (inc VAT)
Bus Pirate Cable
This is an interface cable for the Bus Pirate, designed to connect to its 2x5 I/O header. The cable’s connector is composed of two rows of five 0.1" spaced pins; it’s also polarized, as is the mating connector on-board the Bus Pirate, so you can only connect the cable in one direction. The leads of the cable are terminated with female ends to mate with test hooks. The pin-out of the connector is documented here...
R89.00 (inc VAT)
IC Hook Test Leads
These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. 5 pairs of IC Hook to IC Hook test leads. Comes with Black, Red, Blue, Green, and Yellow colored leads. Features: 14" Long ..
R178.00 (inc VAT)
IC Hook with Pigtail
These are good quality IC test hooks with a male connection wire. Instead of a single hook, these have two hooks that are capable of grabbing very small points (like SOIC IC legs). Comes in a bag of five IC hooks of different colors (black, red, white, blue, and green). We use them with the Bus Pirate logic analyzer harnesses but are very cool on their own. Wire length is 2.5" long. Male pin easily inserts into breadboard or other standard 0.1" connector...
R104.00 (inc VAT)
Infrared Sensor Jumper Wire - 3-Pin JST
Three pin JST connector with red, black, and yellow colors. 5 inch wire outs. This cable comes fully assembled as shown and connects directly to many different Sharp sensors. Quick and easy, this cable will save you 15-20 minutes over making your own wiring harness. If you need this cable and the mating connector, check out the wire assembly in the related products below!..
R22.00 (inc VAT)
Interface Cable - SMA Female to SMA Male (25cm)
This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8") long and has a 50? impedance that can handle frequencies up to 17 GHz. The SMA connectors at each end are small enough for most consumer GPS, cellular, and other RF applications and they use a threaded housing to create strong mechanical connections. These work well for mounting an antenna to the outside of an enclosure, while keeping the electronics neatly inside. Note: If you are looking for an RPSMA interface cable, it can be found here. Documents: Dimensional Drawing SMA Antenna Connectors ..
R89.00 (inc VAT)
JST to Breadboard Jumper (3-pin)
This is a simple jumper adapter cable that comes pre-terminated with a female JST connector on one end and a breadboard hookup pigtail on the other. This cable makes it easy to connect components with a JST connector to a breadboard or an Arduino-based device’s pins. Wire length is 140mm (about 5.5 inches) long. The adapter’s wires have been color coded to Red, Black, and Yellow. Additionally, the female JST connector featuring a basic 2mm pitch while the male hookup pins can easily insert into a standard 0.1" connector. Documents Datasheet ..
R29.50 (inc VAT)
LIDAR-Lite Accessory Cable
This is the same accessory cable found in the LIDAR-Lite v3. The LIDAR-Lite Accessory Cable is terminated with a simple 6-pin JST at one end and a bare wire pigtail at the other. You can use this cable as a replacement to the one you are currently using, as a backup in case of damage, or if you just need a second one. The LIDAR-Lite Accessory Cable is 200mm (~7.8in) long with specific pin-outs found on the second page of the Operation & Technical Manual below. Documents: Operation & Technical Manual ..
R133.50 (inc VAT)
Multimeter Probes - Tweezers
Testing surface-mount components with standard test leads is anything but easy. Everyone has their own method: some people tackle it with teamwork and have a friend (or grad student) hold the probes, some people have adapted a sort of chopsticks-like technique, but the best way by far is probably just to buy these handy tweezer probes! Tweezer probes connect to your existing instrumentation with shrouded banana connectors and allow you to easily test small parts with one hand. The large plastic tweezers are easy to grip and are marked for polarity. Features: Tweezers are 6" ..
R104.00 (inc VAT)
Qwiic Cable - 100mm
This is a 100mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. Each Qwiic Cable’s wires have been color coded to Red, Black, Blue, and Yellow. The SparkFun Qwiic connect system is an ecosystem of I2C sensors, actuators, shields, and cables that make prototyping faster and less prone to error. All Qwiic enabled boards use a common 1mm pitch, 4-pin JST connector. This reduces the amount of required PCB space, and polarized connections mean you can’t hook it up wrong. ..
R37.00 (inc VAT)
Qwiic Cable - 200mm
This is a 200mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. Each Qwiic Cable’s wires have been color coded to red, black, blue and yellow. The SparkFun Qwiic connect system is an ecosystem of I2C sensors, actuators, shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch, 4-pin JST connector. This reduces the amount of required PCB space, and polarized connections mean you can’t hook it up wrong. ..
R37.00 (inc VAT)
Qwiic Cable - 500mm
This is a 50mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. Each Qwiic Cable’s wires have been color coded to red, black, blue and yellow. This cable is used for connecting Qwiic boards that need to be very far away from the controller. Note that I2C signals will degrade over longer distances. We recommend keeping the connections to 1 meter or less. That said, we’ve daisy-chained boards 2 meters (four of these cables) away from a RedBoard successfully. Your mileage may vary. The ..
R52.00 (inc VAT)
Qwiic Cable - 50mm
This is a 50mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. Each Qwiic Cable’s wires have been color coded to red, black, blue and yellow. The SparkFun Qwiic connect system is an ecosystem of I2C sensors, actuators, shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch, 4-pin JST connector. This reduces the amount of required PCB space, and polarized connections mean you can’t hook it up wrong. F..
R22.00 (inc VAT)
Qwiic Cable - Breadboard Jumper (4-pin)
This is a jumper adapter cable that comes pre-terminated with a female Qwiic JST connector on one end and a breadboard hookup pigtail on the other. This cable makes it easy to connect components with a Qwiic connector to a breadboard or an Arduino-based device’s pins. The 28AWG wire’s length is 150mm (about 5.9 inches). The adapter’s wires have been color coded to red, black, blue and yellow. Additionally, the female Qwiic connector features a basic 1mm pitch, while the male hookup pins can easily insert into a standard 0.1" connector. The SparkFun Qwiic connect system is an ecosystem of I..
R29.50 (inc VAT)
Raspberry Pi GPIO Shrouded Header - 2x20
This 2x20 shrouded header has the same number and spacing of pins as a Raspberry Pi so you can easily connect via ribbon cable to the low-level peripherals and get hacking! This through-hole header has 40 0.1"-spaced pins and is keyed for polarity. Check the related items below for the mating cable! Documents: Datasheet ..
R15.00 (inc VAT)
Raspberry Pi Zero Camera Cable
The Raspberry Pi Zero and Zero W are both equipped with a smaller CSI (Camera Serial Interface) port than on a full-sized Raspberry Pi board — luckily, that’s where this cable can help! The Raspberry Pi Zero Camera Cable replaces the pre-existing camera module cable, allowing your Zero or Zero W light and imaging capabilities. This cable measures 15cm from end to end and can easily be swapped in and out. Note: This product only includes the CSI cable and does NOT include a Raspberry Pi Camera Module. The module will need to be purchased separately...
R118.50 (inc VAT)
Ribbon Cable - 6 wire (15ft)
Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing makes a project look more finished than a nice clean wiring harness. This is a 15ft. length of 6-wire ribbon cable. Check the related products below for crimp-on connectors that will fit this cable. Documents: Datasheet ..
R44.50 (inc VAT)
Alligator Test Leads - Multicolored 10 Pack
Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you’re just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them, these spring-loaded clips are a workshop must-have. Each lead in this pack of tern is 50cm long with a rubber shrouded alligator clip on each end. There are five different colors, you get two each of: red, green, white, black and yellow. Dimensions: 50cm long or 0.000269978402 nautical miles..
R59.50 (inc VAT)
Alligator to Alligator Cables
Description: These are standard alligator clip to alligator clip cables. Package contains a pair of red and black cables. Dimensions: 12" ..
R59.50 (inc VAT)
Banana to Test Probe Cables
These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Great, sturdy replacement for multimeter probes. Cables come in red/black pairs. Dimensions: 36" Long..
R74.00 (inc VAT)
BNC to IC Hook Cable
These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Dimensions: 36" Long..
R118.50 (inc VAT)
IC Hook to IC Hook Cables
These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables come in red/black pairs. Dimensions: 36" Long..
R89.00 (inc VAT)
Open Logic Sniffer - Probe Cable Kit
This is the probe cable for Open workbench Logic sniffer. It has a 1×9 connector and 9 leads with tweezer-style test clips. Each cable connects 8 of the 16 buffered input channels, plus ground...
R252.00 (inc VAT)
Raspberry Pi - GPIO Ribbon Cable (6")
This 2x13 flat ribbon-cable fits the GPIO headers on the Raspberry Pi so you can easily connect to the low-level peripherals and get hacking! This cable has 0.1"-spaced connectors and is keyed for polarity. Check the related items below for the mating connector! Features: 6" long Documents: Datasheet ..
R28.00 (inc VAT)
Raspberry Pi - GPIO Shrouded Header (2x13)
This 2x13 shrouded header has the same number and spacing of pins as the Raspberry Pi so you can easily connect via ribbon cable to the low-level peripherals and get hacking! This through-hole header has 26 0.1"-spaced pins and is keyed for polarity. Check the related items below for the mating cable! Documents: Datasheet ..
R15.00 (inc VAT)
Raspberry Pi GPIO Ribbon Cable - 40-pin, 6" (RPi 3, RPi2, B+)
This 2x20 flat ribbon-cable fits the GPIO headers on the Raspberry Pi 3, 2, and B+ so you can easily connect to the low-level peripherals and get hacking! This cable has 0.1"-spaced connectors and is keyed for polarity. Features: 6" long Documents: Datasheet Product Video ..
R59.50 (inc VAT)
Banana to IC Hook Cables
These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables come in red/black pairs. Features: 36" Long ..
R104.00 (inc VAT)
Ribbon Cable - 10 wire (3ft)
Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing makes a project look more finished than a nice clean wiring harness. This is a 3ft. length of 10-wire ribbon cable. Check the related products below for crimp-on connectors that will fit this cable. Documents: Datasheet ..
R18.00 (inc VAT)
Sensor Cable - Electrode  Pads (3 connector)
This is your simple three conductor sensor cable with electrode pad leads. These cables are 24" long and feature a 3.5mm audio jack connector on one end with snap style receptacles for biomedical sensor pads. Each cable comes in a red/blue/black set. Features: 24" Long Documents: Product Video ..
R118.50 (inc VAT)
Ribbon Cable - 6 wire (3ft)
Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing makes a project look more finished than a nice clean wiring harness. This is a 3ft. length of 6-wire ribbon cable. Check the related products below for crimp-on connectors that will fit this cable. Documents: Datasheet ..
R10.50 (inc VAT)
Alligator Test Leads - Multicolored (10 Pack)
Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you’re just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them, these spring-loaded clips are a workshop must-have. Each lead in this pack of tern is 50cm long with a rubber shrouded alligator clip on each end. There are five different colors, you get two each of: red, green, white, black and yellow. Features: 50cm long or 0.000269978402 nautical miles ..
R59.50 (inc VAT)
Alligator Clip with Pigtail (4 Pack)
This is a 4 pack of wires that are pre-terminated with an alligator clip on one end and a hookup pigtail on the other. Alligator clips are a staple part for any workbench and with these cables you will be able to easily incorporate those clips into a breadboard, development platform, or anything else that you would normally be able to attach a hookup wire to. Each Alligator Clip with Pigtail cable has a wire length of 30cm (that’s a little less than 1ft) and a male pin that easily inserts into a standard 0.1" connector. Each pack consists of two red cables and two black cables. Documents: ..
R59.50 (inc VAT)

Store Information